Configuring a Welltech Wellgate 3802 FXO for GnuGk

To use a Welltech Wellgate with the GNU Gatekeeper, you have to switch to Gkmode. Remember to issue a "flash -clean" when you change from p2p to Gkmode.

Sample Wellgate Configuration

usr/config$ h323 -print

H.323 stack relate information
    RAS mode                 : GK mode
    Registration mode        : Gateway
    Gatekeeper IP address    : 10.55.10.51
    Gatekeeper ID            : GK
    Registered e164          : 0
    Registered H323 ID       : gw3
    Gatekeeper Discovery     : On
    Q931 port                : 1720
    RAS port                 : 16640
    RTP port                 : 16384
    RAS TTL time             : 60
    Gatekeeper discovery port: 1718
    Gatekeeper RAS port      : 1719
    Allocated port range     :
              start port     : 1024
              end port       : 65535
    Response timeOut         : 5
    Connect  timeOut         : 200
usr/config$ 

usr/config$ gk -print

Gatekeeper setting relate information
 Enable         : 0
 TTL            : 0
        Already Registration Endpoint:   
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
        H323ID= E164= IP=0 Type=Terminal
 Security       : 0
        Allowded Registration Endpoint:   
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
        H323ID=
usr/config$ 

usr/config$ sysconf -print

System information
    Gateway Service: 1
    DialPlan number of digits: 0
    Inter-Digit time out        : 5
    End of Dial                 :  [ # ] button
    Port status:
        port1: Enabled
        port2: Enabled
    DTMF selection              : H.245 SignalType
    CallAlive auto-disconnection: OFF
    Line seizure mode: None
    2nddial:  Off
    Dial Rule
         outgoing call:
         filter: []   drop: []   insert: [].
         incoming call:
         filter: []   drop: []   insert: [].
    PIN prompt: 0
         set1: 1111
         set2: 2222
    Access code: 0
         set1: 1111
         set2: 2222
    Ring Detect Method: 1
    Ring before Answer: 0
usr/config$ 

usr/config$ voice -print

Voice codec setting relate information
    Sending packet size  : 
            G.723.1      : 30 ms
            G.723.1      : 30 ms
            G.723.1      : 30 ms
            G.723.1      : 30 ms
            G.729        : 20 ms
    Priority order codec : 
            g7231 g7231 g7231 g7231 g729 
    Volume levels        : 
            voice volume : 32
            input gain   : 32
             dtmf volume : 23
 No sound compress & CNG : 
            G.723.1      : Off
            G.723.1      : Off
            G.723.1      : Off
            G.723.1      : Off
    Echo canceller       : On On 
 JitterBuffer Min Delay  : 90
 JitterBuffer Max Delay  : 150
usr/config$



Last updated: 03. May 2011
Page maintained by Jan Willamowius