Configuring a Cirilium 8000 for the GNU Gatekeeper

Configuring a Cirilium 8000 for GnuGk

[H323gw] ;------------------------------------------------------------------------------- ; IMPORTANT !!!!! This file was generated automatically by ; utility for H.323 v1.4 And SIP v2.0 ; ; From: Ini file utility_M2K_v2_48_7_3_1.xls ; Date: 7/15/2003 ; Time: 11:18:25 AM ; Edited by ali Arman (480) 317-1014 ;------------------------------------------------------------------------------- ;------------------------------------------------------------------------------- ; General Feature Parameters ;------------------------------------------------------------------------------- ; Set VoIP protocol type. 4 = H.323 MGControlProtocolType = 4 ; The version of the Media Gateway GatewayVersion = 4.20.10.764 ;------------------------------------------------------------------------------- ; Compression Channel Parameters ;------------------------------------------------------------------------------- ; The first coder used. CoderName = g729 ; The second coder used. CoderName = g7231 ; Is Silence Compression enabled (0 - no, 1 - yes) [default 0] SCE = 1 ; Is Echo Canceling enabled (0 - no, 1 - yes) [default 1] ECE = 1 ; Packets size - How much to multiply packets size [default 1] ; M = n payloads (n = 1,2 or 3) Number of 20 msec payloads (30 msec for G.723) M = 3 ; 0=User propriety FRF.11 syntax to send/receive fax relay. ; 1=Use T.38 protocotol to send/receive fax relay [default 1] UseT38orFRF11 = 1 ; Sets the fax transport mode. 0=disable, 1=relay, 2=bypass [default 1] FaxTransportMode = 1 ; [default 0] 0 = Use redundancy packets for protecting T.38 fax relay stream, ; 1 = Use Forward Error Correction (FEC) algorithm to protect T.38 fax relay ; stream. T38ProtectionMode = 0 ; [default 0] 0-2 (T38ProtectionMode = 0) FaxRelayRedundancyDepth = 2 ; Redundancy of T.38 control packets[default=1] ;FaxRelayEnhancedRedundancyDepth = 2 ; DTMF gain control. Parameter range is -31 dBm to 0 dBm in 1 dB steps. ; default=-11 dBm DTMFVolume = -11 ; 0 = erase digit from voice stream don't relaye to remote, required for ; out-of-band H.245 ; 1 = erase digit from voice stream relay to remote (default) ; 2 = digits remains in voice stream, ; 3 = for DTMF relay per RFC 2833. DTMFTransportType = 0 ; 0 = Erase MFs from voice transport, not relayed to remote. ; 1 = Erase MFs from voice transport, relay to remote (default). ; 2 = MFs are not erased from voice stream. MFTransportType = 1 ; Voice gain control.Parameter range is -31 to +31 db. [default = 0 dB] VoiceVolume = 1 ; PCM input gain.Parameter range is -31 to +31db.[default = 1 = 0 dB] InputGain = 1 ; [default 70] 0-150 msec Dynamic Jitter Buffer Minimum Delay. DjBufMinDelay = 70 ; [default 7] 0-12 Dynamic jitter buffer frame error/delay optimization. DjBufOptFactor = 7 ; Applicable to FXO and T1/E1 CAS interfaces. ; 1 = The Gateway disconnects calls when the end tone is detected. DisconnectOnBusyTone = 1 ;------------------------------------------------------------------------------- ; H323 Parameters ;------------------------------------------------------------------------------- ; Set to 1 to use the Fast Start (fast connect) capability; otherwise, set ; to 0 (default) for normal. Note that without FS, no in-band tones possible. IsFastConnectUsed = 1 ; Set to 0 for FastStart info to be included in the ALERTING (Default) ; Set to 1 for FastStart info to be included in the CONNECT IsFSMediaInfoSendOnConnect = 0 ; Fast Start open media on connect: ; Set to 0 for the receiving side to open voice on an ALERT, before a CONNECT ; is sent (Default) ; Set to 1 for the receiving side to open voice only on a CONNECT message. IsFSOpenMediaOnConnect = 0 ; Set to 1 for the Media Gateway to initiate H.245 on Fast Start on ; send/receive Connect message. ; Set to 0 for the Media Gateway not to initiate H.245 on Fast Start (default) OpenH245OnFS = 1 ; Set to 0 for the Media Gateway to offer the first coder from the coder list ; on receipt of setup. Leave the field at its default of 1 for the Media Gateway ; to choose / match a coder from the full coder list. SendMultipleCodersInFS = 1 ; Set to 1 if you want the gateway to register with a Gatekeeper; ; Set to 0 if otherwise (default), in which case you must route the calls ; using the internal routing tables. IsGatekeeperUsed = 1 ; The IP address of the Gatekeeper GatekeeperIp = x.x.x.x ; The IP address of the 1st Redundant Gatekeeper GatekeeperIp = x.x.x.x ; Set to 1 to allow use of the internal routing table if a Gatekeeper ; is not found. Default = 0. IsGKFallbackUsed = 1 ; Set to 1 to use another (redundant) Gatekeeper if the Gatekeeper is ; not found. Default = 0. IsRedundantGKUsed = 1 ; How much time the client waits if the entire list of GKs is exhausted. ; After this timer, the list is retried. TimeBetweenGKsLoops = 60 ; Time in seconds that the stack waits until it notifies the application ; of failure in response. Default = 10. ResponseTimeOut = 10 ; The number of retransmission retries. Default = 3 MaxRetries = 5 ; Registering the Media Gateway as a terminal is useful when the Gatekeeper ; can only work with terminals and not with Media Gateways. ; 0 = Do not register the Media Gateway as a terminal. (default) ; 1 = Register as a terminal. IsTerminal = 0 ; The time, in seconds, between registrations to the Gatekeeper - used for ; keepalive. Applicable only when the field IsTerminal = 1. ; Otherwise, registration is automatic, according to Gatekeeper request. RegistrationTime = 10 ; Set to 1 to enable the Gatekeeper to remap the destination phone number in an ; ACF message (if the destination phone number is placed in the ; dialedDigits field). Default = 0. CanMapAliases = 0 ; Set to 1 for fax use; otherwise, set to 0. 1 = Fax is sent/received using ; H.323 Annex D, T.38 procedure. ; Remember to update the "Fax" sheet. Default = 0. IsFaxUsed = 1 ; 1 = Out-Of-Band DTMF messages are used. Default = 0. ; If set to 1, set DTMFTransportType = 0 IsDTMFUsed = 1 ; Encoding type of calling phone number in H.225 Setup message. ; Default = 0 (e.164) SourceEncodType = 0 ; Encoding type of the destination phone number in H.225 Setup message. ; Default = 0 (e.164). DestEncodType = 0 ; The E.164 Alias defined here will be inserted into RRQ and all other relevant ; messages. RegistrationPrefix = 40# RegistrationPrefix = 50# ; The H.323 ID defined here will be inserted into source H323-ID for all other ; relevant messages. Default = doesn't exist. H323IDString = [email protected] ; Media Gateway registration type to the Gatekeeper. ; 0: register with e.164 prefix as alias (default) ; 1: register with H.323 ID as alias. REQUIRED by Cirilium Gatekeeper if ; Cirilium gatekeeper is in Dynamic Endpoint mode. GwRegistrType = 2 ; 0 = Do not send DTMFs in Q.931 info message. (default) ; 1 = DTMFs will be sent in H225/Q.931 info message. Is931MsgUsed = 0 ; On this port, the Media Gateway waits/listens out for Setup messages. ; Default = 1720. H225ListenPort = 1720 ; To this port, the Media Gateway will send Setup messages. Default = 1720. H225DialPort = 1720 ; The Timeout when establishing a H.245 connection. Default = 29. H245InitTimeOut = 29 ; 1 = RTP Multiplier will be taken into consideration for an TCS message. ; Default = 1. RTPMultiplierUsed = 0 ; Enables passing of Bearer Capability/Transfer Capabilities from ISDN to IP ; side and vice versa. Applicable only to digital Media Gateways running ; ISDN protocol. EnableTransferCap = 0 ; Enables overwriting of Progress indicator on messages sent to H.323 ; -1: not configured (default) ; 0, 1, 2, 8: Theactual value of PI ProgressIndicator2IP = -1 ; 0 = the gateway will not play the ringback tone to IP [default]; ; 1 = the gateway will play the ringback tone to IP. PlayRBTone2IP = 0 ; 1 = Apply Q.931 Multiplexing. Default = 0 (disabled). EnableQ931Multiplexing = 0 ; Enables H.450.4 hold/retreive [default=0] EnableHold = 0 ; Enables H.450.2 transfer [default=0] EnableTransfer = 0 ; Enables H.450.3 forward. Default = 0. EnableForward = 0 ; Enables H.450.6 call waiting[default 0] EnableCallWaiting = 0 ; Number of call waiting indications to be played to the user NumberOfWaitingIndications = 2 ; Timeout in seconds between one call waiting indication to another TimeBetweenWaitingIndications = 10 ;Added sep 26 by Gary McPherson Gatekeeper ID GatekeeperID = gkprjo102 ;Added sep 30 by Gary McPherson h245 tunneling. IsTunnelingUsed = 1 ;------------------------------------------------------------------------------- ; PSTN Interface & Protocol Parameters ;------------------------------------------------------------------------------- ; 1 = Enables the Media Gateway on detection of LAN, RRQ problems to take out ; digital trunks out-of-service, or play reorder tone instead of dial tone ; on analog Media Gateways[default = 0] EnableBusyOut = 0 ; Sets the PSTN protocol to be used for this trunk. ; 1: E1 Euro (ETSI) ISDN, 2: T1 CAS, 3: T1 RAW CAS, 4: T1 Transparent, ; 5: E1 Transparent 62, 6: E1 Transparent 60, 7: E1 MFR2, 8: E1 CAS R2, ; 9: E1 RAW CAS, 10: T1 PRI NI2, 11: T1 PRI 4ESS, 12: T1 PRI 5ESS 9, ; 13: T1 PRI 5ESS 10, 14: T1 PRI DMS100, 15: J1 Transparent, 16: T1 PRI NTT ; 17: E1 PRI Australian, 18: E1 PRI HongKong Telecom, 19: E1 PRI Korean Telecom ProtocolType = 7 ; 1: A-law is for E1 spans ; 3: u-Law for T1 spans PCMLawSelect = 1 ; Selects the ISDN termination mode. (NOT applicable for CAS) (Default = 0). ; 0: User ; 1: Network TerminationSide = 0 ; Selects the source of the clock (internal or recovered clock from E1/T1 line) ; (Default = 0) ClockMaster = 0 ; Selects the T1 Framing Method to be used for this trunk. (Default 0). ; 0: ESF (E1 or T1) ; 1: SF (T1) FramingMethod = 0 ; Selects the line code method to be used for this trunk. (Default = 0). ; 0: B8ZS ; 1: AMI ; 2: HDB3 (E1 only) LineCode = 2 ; When the PBX is recovering the Clock from the User, TDMBusClockSource = 1 ; should be used. TDMBusClockSource = 4 ; This parameter is relevant only if TDMBusClockSource = 4 PSTNAutoClockEnable = 0 ; Defines the mode of Bchannel negotiation (default=1) ; 0: Preferred ; 1: Exclusive ; 2: Any BchannelNegotiation = 0 ; 0 = non NFAS trunk (default) ; 1 to 4 = NFAS group numberIndicates the NFAS group number for the selected ; trunk. The trunks that belong to same NFAS group will have the same number. ; With ISDN Non-Facility Associated Signaling you can use single D-channel to ; control multiple PRI interfaces.Applicable only for T1 ISDN protocols. ; The "NFAS member" of each trunk in NFAS group is the Trunk ID (0 to 7). NFASGroupNumber = 0 ; D-channel configuration parameter defines primary, backup (optional) and ; B-channels only trunks. Primary trunk contains D-channel that is used for ; signaling.Backup trunk contains backup D-channel that will be used if the ; primary D-channel fails. The other NFAS trunks contain only 24 B-channels, ; without signaling D-channel.Applicable only for T1 ISDN protocols. Backup ; trunk is not supported for DMS PRI variants DchConfig = 0 ; 0 = non NFAS trunk (default), 1 to 4 = NFAS group number. Indicates the NFAS ; group number for the selected trunk. The trunks that belong to same NFAS group ; will have the same number. With ISDN Non-Facility Associated Signaling you can ; use single D-channel to control multiple PRI interfaces. Applicable only for ; T1 ISDN protocols. The "NFAS member" of each trunk in NFAS group is the ; Trunk ID (0 to 7). NFASGroupNumber_1 = 0 ; D-channel configuration parameter defines primary, backup (optional) and ; B-channels only trunks. Primary trunk contains D-channel that is used for ; signaling. Backup trunk contains backup D-channel that will be used if the ; primary D-channel fails. The other NFAS trunks contain only 24 B-channels, ; without signaling D-channel. Applicable only for T1 ISDN protocols. Backup ; trunk is not supported for DMS PRI variants. DchConfig_1 = 0 ; 0 = Send Channel ID only if mandatory (default). ; 1= Send Channel ID in first response; ; 2 = Send Channel ID in Call Proceeding. ISDNInCallsBehavior = 0 ; 0 = Connect Ack is not sent as a response to connect (default); ; 1 = Connect Ack is sent as a response to received connect. Applicable only to ; Euro ISDN, user side outgoing call. ISDNIBehavior = 0 ; Define default cause code for ISDN Q.931 Release Complete to be sent to PSTN ; in case of IP related issues. Default = 34, see below for other options. ; ; 2: No route to specified transit network ; 3: No route to destination ; 4: Send special information tone ;16: Normal clearing ;17: User busy ;18: No user responding ;19: No answer from user (user alerted) ;21: Call rejected ;23: Redirect to new destination ;27: Destination out of order ;29: Facility rejected ;31: Normal - unspecified ;34: No circuit / channel available ;38: Network out of order ;42: Switching equipment congestion ;47: Resources unavailable, unspecified DefaultReleaseCause = 34 ; Default call progress tone timer for CAS interfaces ; Reorder tone is played to PSTN following a call failure, upon expiration of the ; timer (in seconds). Not used for ISDN interfaces. ; TimeForReorderTone = 10 ; R2 MF Calling Party's category. The parameter provides information about the ; calling party, such as national or international call, operator or subscriber ; and subscriber priority. ; Range: 1 - 15, defining one of the R2 MF tones (default = 1) R2Category = 1 ; Enables overwriting of Progress indicator on messages sent to ISDN trunk ; -1: not configured (default) ; 0, 1, 2, 8: Theactual value of PI ProgressIndicator2ISDN = -1 ; 0 = the gateway will not play a ringback tone to Telco; ; 1 = the gateway will play a local ringback tone to Telco. ; 2 = the ISDN gateway will not play the ringback tone to Telco, and the ; ISDN PI value will be mapped from received H.225 messages.[default 2] PlayRBTone2TEL = 2 ; The Progress Tones filename. CallProgressTonesFileName = 'usa_tones_03.dat' ; Default = 1. 1 = Burn the Progress Tones file. BurnCallProgressTonesFile = 1 ; The name of the file containing a specific CAS protocol definition ;CASfileName = 'E_M_WinkTable.dat' ;this line was added by Gary McPherson for Brazilian R2 CASfileName = 'R2_Brazil_NoAni.dat' ; 1 = To burn the CAS definition file (default = 0) BurnCASfile = 1 ;------------------------------------------------------------------------------- ; Dial Plan and Call Routing Parameters ;------------------------------------------------------------------------------- ; When set to 0, the individual channels need to be assigned phone numbers ; (extentions) for internal call routing to work; AND an incoming ip-to-pstn ; call's DNIS needs therefore to contain at least the channel's extention number. ; When set to 1, a terminating gateway will pick the first free channel. ; For originating gateways, this parameter has no relevance, other than ANI. IsUseFreeChannel = 1 ; Phone numbers for endpoints (channels) ;------------------------------------------------------------------------------- ; Must use if IsUseFreeChannel = 0 ; Do not use if Trunk Grouping is in use. ChannelList = 0,30,8001 ; Number Translation and Manipulation Parameters ;------------------------------------------------------------------------------- ; Number modification mode of ip-to-pstn calls: ; 0 = first route the call then perform the manipulation on the destination ; phone number (default). ; 1 = first perform the manipulation on the destination phone number, then ; route the call. RouteModeIp2Tel = 0 ; Number modification mode of pstn-to-ip calls: ; 0 = first route the call then perform the manipulation on the destination ; phone number (default); ; 1 = first perform the manipulation on the destination phone number, then ; route the call. RouteModeTel2Ip = 0 ; Up to three NumberMap statements each direction. !!ordered list!! ; Usage: NumberMapTel2IP = a,b,c,d ; ; a : Match prefix (* is allowed as wildcard) ; b : number of digits to be deleted from left ; c : digit string to be inserted as prefix after deletion, or 'none' ; d : (optional) number of original digits left in the resulting string, ; counting from right. Zero deletes all digits in the original string. ; ; See below for examples ;------------------------------------------------------------------------------- ; Destination Phone Number Manipulation Rules for calls to IP ; Prefix of 4 digits will be deleted from phone numbers that starts with 9723 ;NumberMapTEL2IP = 9723,4,None ; Prefix of 3 digits will be deleted from phone numbers that starts with 972 ; and 0 will be added at the beginning ;NumberMapTEL2IP = 972,3,0 ; Only 4 last digits will remain from phone numbers with prefix 03. ;NumberMapTEL2IP = 03,0,None,4 ; Phone numbers that start with 4 and whose length is 4 will have 03539 added. ;NumberMapTEL2IP = 4XXX,0,03539 ;NumberMapTEL2IP = 972,3,0,$$,0,0 ;NumberMapTEL2IP = 972,3,0,$$,$$,0 NumberMapTEL2IP = 2125824987,0,10# NumberMapTEL2IP = 2137234987,0,10# NumberMapTEL2IP = 2137234988,0,30# NumberMapTEL2IP = 2125824988,0,30# ;------------------------------------------------------------------------------- ; Destination Phone Number Manipulation Rules for calls to PSTN ; Prefix of 4 digits will be deleted from phone numbers that start with 9723. ;NumberMapIP2TEL = 9723,4,None ; Prefix of 3 digits will be deleted from phone numbers that start with 40# glm. NumberMapIP2TEL = 40,3,None NumberMapIP2TEL = 50,3,None ; Prefix of 3 digits will be deleted from phone numbers that start with 972, and ; 0 will be added at the beginning. ;NumberMapIP2TEL = 972,3,0 ; Only the last 4 digits will remain from phone numbers with prefix 03. ;NumberMapIP2TEL = 03,0,None,4 ; Phone numbers that start with 4 and whose length is 4, will have 03539 added. ;NumberMapIP2TEL = 4XXX,0,03539 ;------------------------------------------------------------------------------- ; Source Phone Number Manipulation Rules for calls to IP ; Prefix of 4 digits will be deleted from phone numbers that start with 9723. ;SourceNumberMapTEL2IP = 9723,4,None ; Prefix of 3 digits will be deleted from phone numbers that start with 972 ; and 0 will be added at the beginning ;SourceNumberMapTEL2IP = 972,3,0 ; Only 4 last digits will be remaind from phone number with prefix of 03. ;SourceNumberMapTEL2IP = 03,0,None,4 ; To phone numbers that starts with 4 and its length is 4 will be added 03539 ;SourceNumberMapTEL2IP = 4XXX,0,03539 ;------------------------------------------------------------------------------- ; Source Phone Number Manipulation Rules for calls to PSTN ; Prefix of 4 digits will be deleted from phone numbers that starts with 9723 ;SourceNumberMapIP2TEL = 9723,4,None ; Prefix of 3 digits will be deleted from phone numbers that starts with 972 ; and 0 will be added at the beginning ;SourceNumberMapIP2TEL = 972,3,0 ; Only 4 last digits will be remaind from phone number with prefix of 03. ;SourceNumberMapIP2TEL = 03,0,None,4 ; To phone numbers that starts with 4 and its length is 4 will be added 03539 ;SourceNumberMapIP2TEL = 4XXX,0,03539 ; To phone numbers that starts with 40# and its length is 3 40# will be deleted ;SourceNumberMapIP2TEL = 30#,3,None ; Trunk Group Configuration Table ;------------------------------------------------------------------------------- TrunkGroup_1 = 0/1-10,40 TrunkGroup_2 = 0/11-20,50 ;Below definitions is dummy - just to complete the E1 span TrunkGroup_3 = 0/21-30,70 ; TrunkGroup Routing Table ;------------------------------------------------------------------------------- PSTNPrefix = 40#,1 PSTNPrefix = 50#,2 ;PSTNPrefix = 03,2 ;PSTNPrefix = 04,3 ; Prefix Routing Table ;------------------------------------------------------------------------------- ; not used with GK Prefix = 21,a.a.a.a ;Prefix = 4321,10.2.10.1 ; Secures incoming calls from IP. Rejects calls from IP addresses not defined ; in prefix routing table above. (Default = 0). SecureCallsFromIP = 0 ; When the gateway is on theorigination side of the call, set this to 1 to ; add Trunk Group ID at the beginning of the destination phone number. AddTrunkGroupAsPrefix = 0 ; To enable special digits "*" or "#" to be dialed, configure 1. Default = 0. IsSpecialDigits = 1 ; Source and Destination numbering type. Default = 0. ; 0: Unknown, 1:International number, 2: National Number, 3: Network specific ; number, 4: Subscribe number, 6: Abbreviated number, 7: reserved SourceNumberType = 0 DestNumberType = 0 ; Source numbering plan. Default = 0. ; 0: Unknown, 1: ISDN/Telephony numbering plan, 3: Data numbering plan, ; 4: Telex numbering plan, 8: National Standard numbering plan, 9: Private ; numbering plan, 15: reserved SourceNumberPlan = 0 DestNumberPlan = 0 ;------------------------------------------------------------------------------- ; LAN / IP Parameters ;------------------------------------------------------------------------------- ; Set to 0 when working with 10 Base-T hubs. (Default = 4, Auto-negotiation). EthernetPhyConfiguration = 0 ; 0-7, Sets the value of the IP precedence field in the IP header for all ; the packets to be generated from this gateway. [Default 0] IPPrecedence = 5 ; 0,1,2,4,8, Sets the value of the IP Type Of Service field in the IP header ; for all the IP packets to be generated from this gateway. [Default 0] IPTOS = 0 ; 1 = Enable (the Media Gateway will send a DHCP request to configure its ; IP address and other network parameters). ; 0 = Disable (default). DHCPEnable = 0 ; Number of BootP retries. ; 1 = Single BootP retry. ; 2 = Two BootP retries (3 seconds). ; 3 = Three BootP retries (default, 6 seconds). ; 4 = Ten BootP retries (30 seconds). ; 5 = Twenty BootP retries (60 seconds). ; 6 = Forty BootP retries (120 seconds). ; 7 = One hundred BootP retries (300 seconds). ; 15 = Infinite number of BootP retries. BootPRetries = 3 ;------------------------------------------------------------------------------- ; Management and Diagnostic Parameters ;------------------------------------------------------------------------------- ; When Syslog is enabled, the port must be 514 [Default = 1] EnableSyslog = 1 ; The IP address of the LogServer (when LogOutputType is SYSLOG) SysLogServerIP =y.y.y.y ; format of log messages (0-name, 1-time, 2-name & time, 3-syslog) [Default 0] ;LoggerFormat = 3 ;Keys for sysLog info detail GWLoggerFlags = lgr_flow,D2 GWLoggerFlags = lgr_psbrdif,D2 GWLoggerFlags = lgr_stack,D2 ; Enables the Media Gateway to send CDR report to configured output. EnableCDR = 0 WebLogoText = Cirilium 8000 UseLogoInweb = 1 ; Resetting the Web Password to a default one [No Value] ; ResetWebPassword ; Enables \ Disables Web Management [Default 0] DisableWebTask = 0 ; Enables/Disables changing parameters from web browser [Default 0] DisableWebConfig = 0 ; Enables/Disables changing parameters by SNMP manager [Default 0] DisableSNMP = 0 ; SNMP manager IP SNMPManagerIP = 10.2.10.1 ; HTTP port used for Web management (default = 80) HTTPport = 80